master station

Communication protocol conversion processor has the function of MODBUS slave station and HOST LINK master station, it can communicate with host computer and PLC, which followed MODBUS communication protocol and HOST LINK communication protocol respectively.

转协议通信器同时具备MODBUS从站和HOST Link主站的功能，与上位机通信时遵循MODBUS通信协议，与PLC通信时遵循HOST Link通信协议。

It adopts the classic model view controller ( MVC) structure, which is consisted by tissue bank substation in all hospitals and tissue bank master station in telecom server room.

系统采用了典型的MVC架构。系统在使用的时候由分布在各个医院的样本库分站以及部署在电信机房的样本库总站两部分组成。

This paper mainly presents the ammeter selection of this system and design idea of master station, describes the design of terminal station from hardware and software and provides the feasible methods for the reliability of the system.

对远程抄表系统中电能表的选择和主战的设计思路给予说明，分别从软件和硬件上论述了终端站的设计，对系统的可靠性也提出具体的可行性措施。

Because of the limitation of monitoring master station, we can not apply static IP address, so we put a server at the IDC room of China Telecom, and then apply a static IP address for the server.

由于监控主站条件的限制，不能申请到固定IP地址，所以在电信IDC机房托管一台服务器，同时申请一个固定IP地址。

At ordinary times, hospitals apply the inner tissue bank to collect and manage their data, while tissue bank master station to collect data from all hospital to share.

医院平时使用部署在自己医院内部的样本库分站收集和管理自己的数据，而样本库总站用来收集所有的医院数据以便于共享。

This issue uses the encountered problem, from the perspective of integration of nobody duty master station and distribution automation master station, to discuss the key techniques of the implementation of integration of distribution and dispatching.

本论文针对在工程规划和实施过程中重点解决的问题，从无人职守主站和配网自动化主站的整合方面，论述了一体化设计的关键技术。

According to the requirement Hierarchic Management model, the distributed design is divided into primary master station and secondary master station.

分布式设计方案按照分级管理的要求，从上而下分为一级主站和二级主站两个层次。

An integrated load management mode for large customers is proposed. The structure of an actual load management system, the features of its data acquisition terminal and the function of its master station are presented.

文章提出了大客户负荷集成管理的模式，并介绍了一个实际的负荷管理系统的结构及其数据采集终端的特点和主站的功能。

Beginning with the PROFIBUS field bus access protocol, this paper studies the time of data transmission of survey controlling system, and obtains two conclusions of increasing the timeliness of the field bus through the way of analyzing the survey controlling cycle of the single master station.

从PROFIBUS现场总线的存取协议出发，着重研究测量控制系统的数据传输时间并从单主站的测量控制周期的分析中得出了提高现场总线实时性的两个结论。

The communication between the synthesis managing station and the network master station is implemented with microwave mode.

主站和管理主机以微波方式实现通信。

Design on the Software of Master Station of Automatic Meter Reading System

用电自动抄表系统主站管理软件的设计

The process whereby a master station requests slave station to indicate its identity or its status.

主站要求从站表明其标识或状态的过程.

This article discusses components of a 300 MW unit coordinated control system, including the forming of actual load demand, boiler demand and heat signal, turbine master station and boiler master station.

论述菏泽电厂300MW机组协调控制系统构成，包括实际负荷指令的形成、锅炉指令与热量信号、汽轮机主控站和锅炉主控站。

The paper presents how the sub master station of the SCADA system in Lijin processes the wrong action of telesignalling from the hardware stucture remoulding and software design.

介绍了利津供电公司SCADA系统的RTU分站系统从硬件结构改造和软件设计两方面对遥信误动的处理，同时编写出了遥信误报判断的程序，并与主系统程序连接。

Remote meter reading system aggregates master station, remote meter terminal, and electrical energy meter, realize all-round a automatic system which acquire, analyses electrical energy of sending, conveying, assigning network automatically, then calculate the expense.

远程抄表系统是集主站系统、远程抄表终端、电能表于一体的，全面实现发、输、配电网用户电能量的自动采集、分析与计费功能的自动化系统。

The master station in control room and all sub-stations in the field run stably. The function requirements of real-time monitoring and control of flare system in control room, is totally satisfied, and the safety of production equipments is ensured in whole plant.

控制室的主站和现场的分站都运行稳定，完全实现了在控制室内对整个火炬系统进行实时监控的功能，为全厂各个生产装置提供了安全的保证。

The professional test method for acceptance test on power grid dispatching automation system ( master station system) is described in this paper.

阐述了电网调度自动化系统（主站系统）验收的专业测试方法。

The control system of flexible manufacturing system is designed as a single master station mode of PROFIBUS-DP in this paper.

采用PROFIBUS-DP单主站的网络配置模式实现了柔性加工系统的控制系统设计。

At last, the test results of time synchronization between the signal of master station of the "Donghai" Chain of "Changhe 2" navigation system and UTC ( NTSC), kept by the National Time Service Center are presented.

最后，给出了长河二号东海台链的主台信号与国家授时中心的UTC（NTSC）之间的同步实验结果。

System Software of a μ P-Based Telecontrol Equipment for Master Station A Information management system software based on graphical user interface which is programmed with Visual C++ 6.0 is installed on the workstation.

该系统由配电变压器数据采集装置和数据分析工作站组成，其中的数据分析工作站配备有应用Visual c++6.0开发的图形化后台信息管理系统软件。

The master station sends parameters of power control period, power setting, setting depreciation coefficient, alarm time and control turns to the data acquire terminal of special transformer and the terminal will set the corresponding parameters after receiving the order.

主站依次向专变采集终端下发功控时段、功率定值、定值浮动系数、告警时间、控制轮次等参数，终端收到这些命令后设置相应参数。

The software in master station contains eight modules and its test running is all right.

主站管理软件包括八个模块，试运行情况良好。